Posts By: Asian Academy

2 Myths About Heat Pipes Busted – Best Piping Institute in India

2 Myths About Heat Pipes Busted

Myth #1: If heat pipes break, they will get liquid on my electronics.

Fact: Heat pipes rarely, if ever, break. And if they do, the small amount of liquid held in the pipe would be fully saturated into the wick and extremely unlikely to drip or damage your electronics.

Heat Pipes are inherently robust and are a purely passive system that does not wear down over time as active systems often do. A well-engineered heat pipe would require cutting or a copious amount of repeated bending to break. This is one of the reasons why heat pipes are used in industries such as aerospace and defence, where high reliability and long lifetimes are required.

If the seal of a heat pipe were to be broken, the tiny amount of liquid actually within the pipe would be fully saturated into the wick so that no fluid would drip out. The wick would keep any liquid within the heat pipe with capillary forces. Furthermore, heat pipes are charged with a vacuum while being filled. This process ensures that a certain amount of the fluid contained in the pipe is always in vapour form and therefore will not drip.

Myth #2: Heat pipes are heavy.

Fact: Heat pipes can remove more weight than they add to an assembly.

Engineers from Top Piping Institutes in India often integrate heat pipes into custom cooling solutions in order to decrease the weight or volume of the overall solution. Although most often made of copper, heat pipes are hollow and can decrease the weight of your solution while improving thermals in a variety of ways. In many assemblies, heat pipes are used to transfer heat to a cooler, more open area of the device, where a fan can be added to decrease the size and weight of your cooling solution.

Another common example is replacing a traditional copper spreader with an aluminium heat sink base that has embedded heat pipes. These heat pipes can be arranged to target spreading to specific locations while reducing the amount of copper needed and therefore reducing the overall weight and cost of your solution.

Are you looking for Piping Engineering Institute In Mumbai

Pune Address : 5th floor, A-Wing, Office No. 74-79, K.K. Market, Sr. No. 674-675, Dhankawadi, Pune-Satara rd, Pune-411043.

Phone : +91 20 24361091 / +91 20 24361099

Mobile No : +91 9822086802 / +91 9822093666

Email ID : contact@asianacademy.org.in,

mrjoshi.piping@yahoo.com

&

Mumbai Address : L-326, Dreams The Mall, Near Bhandup Railway Station, Bhandup West, Mumbai- 400078, Maharashtra, India.

Mobile No : +91 9822086802 / +91 9822093666

Email ID : mrjoshi.pipingmumbai@yahoo.com

Website:- http://www.asianacademy.org.in

Basics of Piping System – Best Piping Design Institute in India

Basics of Piping System

Piping Engineers studying from the best piping design institutes in India are trained about the basics of the piping system. A piping system is an assembly of pipe, fittings, valves, and speciality components. All piping systems are engineered to transport a fluid or gas safely and reliably from one piece of equipment to another.

Piping is divided into two main categories:

Small bore lines and Large bore lines

As a general practice, those pipelines with nominal diameters 2” (50mm) and under are classified as small bore and greater than 2” (50mm) NB as the large bore. In this blog, let’s explore the basics of the piping system, which is all about designing, fabricating and constructing lines for conveying fluids.

Abbreviations of Piping System:

NPS – Nominal Pipe Size

DN – Diamètre Nominal

ID  – Inside Diameter

OD – Outside Diameter

SCH – Schedule (Wall Thickness)

STD – Standard Weight Wall Thickness

XS – Extra Strong Wall Thickness

XXS – Double Extra Strong Wall Thickness

Basics of Pipe Sizes

Pipe sizes are designated by two numbers: Diameter and Thickness. In the US, pipe size is designated by two non-dimensional numbers: Nominal Pipe Size (NPS) and schedule (SCH). Let’s look at some key relationships:

Nominal pipe size (NPS) is used to describe a pipe by name only. Nominal pipe size (NPS) is generally associated with the inside diameter (ID) for sizes 1/8” to 12”. For sizes 14” and beyond, the NPS is equal to the outside diameter (OD) in inches.

Outside diameter (OD) and inside diameter (ID), as their names imply, refer to the pipe by their actual outside and inside measurements. Outside diameter (OD) remains same for a given size irrespective of pipe thickness.

Schedule refers to the pipe wall thickness. As the schedule number increases, the wall thickness increases, and the inside diameter (ID) is reduced.

Nominal Bore (NB) along with schedule (wall thickness) is used in British standards classification.

Piping Design Course in Pune will help you learn and master these basics thoroughly.

Reference: Process Piping Fundamentals, Codes and Standards by A.Bhatia

If you want to know more about Prospects of Piping and Process Engineering

Pune Address : 5th floor, A-Wing, Office No. 74-79, K.K. Market, Sr. No. 674-675, Dhankawadi, Pune-Satara rd, Pune-411043.

Phone : +91 20 24361091 / +91 20 24361099

Mobile No : +91 9822086802 / +91 9822093666

Email ID : contact@asianacademy.org.in,

mrjoshi.piping@yahoo.com

&

Mumbai Address : L-326, Dreams The Mall, Near Bhandup Railway Station, Bhandup West, Mumbai- 400078, Maharashtra, India.

Mobile No : +91 9822086802 / +91 9822093666

Email ID : mrjoshi.pipingmumbai@yahoo.com

Website:- http://www.asianacademy.org.in

Role of a Quality Control Inspector – Piping Inspector Course in India

Role of a Quality Control Inspector

The Piping and Mechanical Quality Control Inspector offers on-site knowledge of quality control and assurance. Piping Inspector Course in India states that the responsibilities of a Quality Control Inspector include conducting routine inspections, testing, and material compliance of services, products and overall standard of strike’s Quality Management System.

Project Specific Roles and Responsibilities:

  • Inspect all welding on above ground piping for conformance to codes and client requirements.
  • Inspect all welds against the detailed Spool Sheets for conformance to general arrangement, material grade, and dimensional compliance.
  • Inspect, record, and mark all received pressure parts and bolt-up materials.
  • Review MTRs for specification conformance and maintain files about project-specific and surplus materials.
  • Monitor storage and use of materials for designated applications on a per-project basis.
  • Maintain surveillance of welding and fitting practices for conformance to WPS, Code, and client specific requirements (i.e. preheat, tacking, electrode storage, weld parameters).
  • Receive and review all NDT reports for completeness and accuracy of code and client required information and correct identification of welds per location and line #.
  • Provide field surveillance of subcontractor activities such as NDE, boring, spray insulation, Hydro-torque, etc.
  • Supervise/participate in the production of weld maps and the markup of as built
  • drawings with a welder, NDE, and MTR information.
  • Piping Engineering Course in Mumbai emphasises on assisting in the production of hydro test packages, joint torque packages, and final redline
  • drawings for permanent record and client turnover.
  • Provide inspection of assemblies before hydro testing to ensure all MTRs, NDE, and
  • visual inspections are complete and issue punch list/test clearance forms before hydro.
  • Witness hydro tests to ensure all required analysis and calibration documentation are available
  • and relevant and that the test procedures conform to Park L, code and client requirements.
  • Receive, review and file/submit all field reports related to civil and earthworks (i.e. ditching, backfill, crossing reports, etc.)
  • Build a photo record of the project as laid out by project management personnel.
  • Perform final acceptance inspections of pipelines and facilities for conformance to
  • P&IDs, piping isometric drawings, and client specs. Record results on inspection checklists or other designated reporting formats.

Non-project Responsibilities Roles and Responsibilities:

  • Maintenance of testing equipment calibration records.
  • Keeping abreast with code revisions and client specifications.
  • Gaining additional certifications and code endorsements as needed.
  • Development of training aids and instructional manuals.

Are you looking for Piping Engineering Institute In Mumbai

Pune Address : 5th floor, A-Wing, Office No. 74-79, K.K. Market, Sr. No. 674-675, Dhankawadi, Pune-Satara rd, Pune-411043.

Phone : +91 20 24361091 / +91 20 24361099

Mobile No : +91 9822086802 / +91 9822093666

Email ID : contact@asianacademy.org.in,

mrjoshi.piping@yahoo.com

&

Mumbai Address : L-326, Dreams The Mall, Near Bhandup Railway Station, Bhandup West, Mumbai- 400078, Maharashtra, India.

Mobile No : +91 9822086802 / +91 9822093666

Email ID : mrjoshi.pipingmumbai@yahoo.com

Website:- http://www.asianacademy.org.in

Prospects of Piping and Process Engineering

Piping Engineering is one of the best and most prestigious job-oriented course for mechanical and chemical engineers. It is the gateway to a highly rewarding career. According to various surveys, the demand for pipeline engineers in India has increased by more than 45%, in the past few years.

The following job prospects sum up the scope of the Piping Engineering Course:

Piping Co-ordination

Pipeline engineers need to review Basic Engineering Package (BEP), attend project start meeting, prepare scope-of-work, and estimate engineering person-hours. As project coordinators, these individuals look for missing information and communicate the loopholes to the client.

Plot Plan Development

Process engineers excellent at planning and developing units are very much in demand today. Piping Engineering Diploma in India trains these individuals to execute a common plot plan development philosophies like the block system, flooding, process flow, and roads and ensure proper functioning of petrochemical components.

Piping Codes and Standards

Specific International Codes and Principles govern the work of all pipeline and process engineers. Professionals must adhere to the standard work ethics and standards. A Pipeline Engineer must have thorough clarity about these codes and laws and execute work, under these norms. Piping Engineering Course in Pune helps engineers learn about these codes and standards.

Process Engineering Documents

For any engineering project, proper referencing and documentation of drawings are extremely important. It is the process engineers job to amalgamate all engineering drawings and prepare a consolidated document before the client.

Pipe Stress Analysis

Since pipe systems work in different temperature and pressure conditions, it brings a lot of stress to the components. It is the job of a pipe stress analyst to figure out the cause of stress, conduct static or dynamic stress analysis, and prepare a pipe stress report.

Process Instrumentation

Every process instrument has input, output, and hardware functions. As a pipeline supervisor, one must ensure the proper modelling and maintenance of the devices, in appropriate locations.

Pipeline and Process Engineering entails a very bright future for mechanical and chemical engineers.

Pune Address : 5th floor, A-Wing, Office No. 74-79, K.K. Market, Sr. No. 674-675, Dhankawadi, Pune-Satara rd, Pune-411043.

Phone : +91 20 24361091 / +91 20 24361099

Mobile No : +91 9822086802 / +91 9822093666

Email ID : contact@asianacademy.org.in,

mrjoshi.piping@yahoo.com

&

Mumbai Address : L-326, Dreams The Mall, Near Bhandup Railway Station, Bhandup West, Mumbai- 400078, Maharashtra, India.

Mobile No : +91 9822086802 / +91 9822093666

Email ID : mrjoshi.pipingmumbai@yahoo.com

Website:- http://www.asianacademy.org.in